◆ contact: beatmaster90@naver.com
1. Please send the URL (current page web address)
or the title of this page
2. include your name (for easier email management)
(may not respond fast, depending on order status, etc. but will respond eventually. processing request mails by chronological order.)
◆payment methods
(contact me via email)
1. Paypal
2. WISE
- usually similar processing speed compared to Paypal
- Cheaper due to lower fees from WISE
- For Wise make your account here:
https://wise.com/gb/account/
◆Details:
------- crack / shock resistant barrel, cap, grip design
------- pen material: Ultem (Germany)
------- feed material: Ebonite (Japan)
------- converter not included
(Use Pilot Con-40 / Con-70, or eyedropper(don't recommend as carry around pen)
(I'm not a retail seller of pilot, so it isn't possible for me to get pilot converters in batch.
please purchase from local sellers)
------- grip section: 0.01mm accuracy, precision machined, solid & thick one piece design
------- barrel & cap: plain round / dodecagon precision machined, solid & sturdy one piece design
------- barrel & cap will perfectly line up, with typical closing force
* may leave extra 1~2 microns, because surfaces may wear over years of use.
(a precision of ±0.001mm ( ± 1 micron) is strictly followed to achieve proper positioning)
------- nib: BOCK (Germany)
nib size "M" (same thickness as mechnical pencil 0.7mm)
may be a bit thinner than regular M, due to my additional nib grinding
Nib surface micro blasted treatment
The following has been done for the nib:
1. precise nib selection from a large batch
2. nib surface micro blasting
3. nib friction fit installation
4. precision heat setting of ebonite feeder, to perfectly match the feed to the nib
5. nib slit size adjustment
6. nib point alignment
7. nib baby bottom removal (Eliminate Skipping)
8. nib scratchiness reduction
9. nib smoothing / test
10. nib overall inspection
------- feed: eureka 5th gen V3 ebonite feeder
solid & sturdy one piece design
("The most precise and complex structured ebonite feed ever created")
details regarding the feeder: https://eurekafp.com/670, https://eurekafp.com/588, https://eurekafp.com/590
* you can purchase extra / different kinds of ebonite feeder,
see here: https://eurekafp.tistory.com/670
--------------------------------------------------------------------------------
<<<Important Information >>>
◆How to Receive Notification For Newly Made Pens: https://eurekafp.com/notice/432
◆ (TIPs) Easy Roll Stoppers Four Your Eureka Pens: https://eurekafp.tistory.com/560
◆ What is micro blasted nib?: https://eurekafp.tistory.com/591, https://eurekafp.com/731
◆ Oring added to grip section for Con-70: https://eurekafp.tistory.com/712
◆ How to use Con-70 properly for Eureka pens: https://eurekafp.com/689
◆ How to install Con-70 & important quirks: https://eurekafp.com/641 , https://eurekafp.com/681
◆ PEEK Durability Test: https://eurekafp.com/676
---------------------------------------------------------------------------------
◆ Dodecagon Cigar Symmetry PEEK + ebonite feed (5g v3) + blasted plain nib
* spare o-rings for grip section included.
* o-ring is already installed, so please do not install another one!
--- $154 (Paypal)
--- $145 (Wise)
◆ Shipping: $25 (EMS Express, 7 days, full coverage insurance)
*below pen in the photo will be sent
Left: hourglass arc grip Right: full arc pipe grip (B grade overall quality, minor defects --- $132 (paypal))
*just water inside grip, not defect
